Jeep Grand Cherokee

1993-1999 of release

Repair and car operation



Jeep Grandee Cheroki
+ Jeep Grand Cherokee brand Cars
+ Settings and routine maintenance
+ Ryadny six-cylinder engine
+ V8 Engine
+ Procedures of the general and major maintenance of the engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
- Brake system
   General information
   System of anti-blocking of brakes (ABS) - the general information
   Replacement of blocks of disk brake mechanisms
   Removal, major maintenance and installation of a support of the disk brake mechanism
   Condition check, removal and installation of a brake disk
   Replacement of boots of drum-type brake mechanisms
   Removal, major maintenance and installation of wheel cylinders
   Removal and installation of the combined valve (regulator)
   Removal and installation of the main brake cylinder
   Check of a condition and replacement of brake hoses and lines
   Pumping of brake system
   Functioning check, removal and installation of the vacuum amplifier of brakes
   Functioning check, removal, installation and adjustment of the sensor switch of stoplights
   Adjustment of the parking brake
   Replacement of cables of a drive of the parking brake
   Replacement of boots of the parking brake (disk brake mechanisms of back wheels)
+ Suspension bracket and steering
+ Body
+ System of onboard electric equipment
+ Governing bodies and operation receptions



Adjustment of the parking brake

Models of 1993 вып.

 PERFORMANCE ORDER

  1. Make sure that drums (or disks) brake mechanisms of back wheels rotate freely, without zakusyvaniye, then completely cock the lever of the parking brake.
  2. To Poddomkratta a car back also establish it on props.
  3. With chalk or fatty pencil mark the provision of an adjusting nut on the tip of a natyazhitel of a cable equipped with a carving.
  1. On models of 1993 вып. with chalk or a fatty pencil mark the provision of an adjusting nut (the left arrow) on the tip of a natyazhitel of a cable equipped with a carving, then screw a nut approximately on 13 mm more deeply on a tip; if carrying out replacement of a back cable is planned, compress its clamp (the right shooters) a small shlangovy collar of worm type.
  1. Screw a nut more deeply on a tip of a natyazhitel approximately on 13 mm. If lengths of a carving part of a tip it appears insufficiently, replace a natyazhitel (The section Replacement of cables of a drive of the parking brake). It is not necessary to try to improve a natyazhitel or to use it repeatedly.
  2. Release the lever of the parking brake and make sure that back wheels rotate freely.
  3. Clean jacks and lower the car.
  4. Check functioning of brakes on a bias.

Models since 1994 вып.

 PERFORMANCE ORDER

  1. Make sure that drums (or disks) brake mechanisms of back wheels rotate freely, without zakusyvaniye, then completely cock the lever of the parking brake.
  2. To Poddomkratta a car back also establish it on props.
  3. Put on a rod of a natyazhitel a label approximately in 6,5 mm from an arm of a natyazhitel.
  1. On models 1994 and 1995 of вып. put on a rod of a natyazhitel a label at distance about 6.5 mm from an arm.
  1. Tighten an adjusting nut on the balance weight so that the label on a rod of a natyazhitel was combined with his arm.

On any of the reasons do not tighten and do not weaken an adjusting nut of a natyazhitel after completion of adjustment!

  1. Release the lever of the parking brake and make sure that back wheels of the car rotate freely.
  2. Clean jacks and lower the car.
  3. Check functioning of brakes on a bias.