Jeep Grand Cherokee

1993-1999 of release

Repair and car operation



Jeep Grandee Cheroki
+ Jeep Grand Cherokee brand Cars
+ Settings and routine maintenance
+ Ryadny six-cylinder engine
+ V8 Engine
+ Procedures of the general and major maintenance of the engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
- Suspension bracket and steering
   General information
   Removal and installation of the forward stabilizer of cross-section stability and its plugs
   Removal and installation of forward shock-absorbers
   Removal and installation of a cross-section jet bar of a forward suspension bracket
   Removal and installation of levers of a forward suspension bracket
   Removal and installation of screw springs of a forward suspension bracket
   Removal and installation of rotary fists
   Replacement of spherical hinges
   Removal and installation of a bar of the back stabilizer of cross-section stability
   Removal and installation of back shock-absorbers
   Removal and installation of a cross-section jet bar of a back suspension bracket
   Removal and installation of levers of a back suspension bracket
   Removal and installation of screw springs of a back suspension bracket
   Removal and installation of a steering wheel
   Condition check, removal and installation of a steering drive
   Removal and installation of the steering mechanism
   Removal and installation of the pump of system of hydrostrengthening of a wheel
   Pumping of system of hydrostrengthening of a wheel
   Wheels and tires - the general information
   Corners of installation of forward wheels - the general information
+ Body
+ System of onboard electric equipment
+ Governing bodies and operation receptions



Removal and installation of a steering wheel

All considered models are equipped with a safety cushion. The pillow constantly is in the "guarded" condition and can work to (be inflated) at any moment at the connected battery. In order to avoid casual operation of a pillow (and receiving as a result of a trauma) each time at carrying out any works with components of system of safety disconnect a negative wire from the battery. After a wire detachment from the battery before starting to work wait at least two more minutes (the system is equipped with the condenser to which needs time for a discharge). In more detail about work of system of safety see. Head System of onboard electric equipment.


 PERFORMANCE ORDER

  1. Establish operated wheels of the car rectilinearly. Disconnect a negative wire from the battery.

If the audiosystem of your car is equipped with a security code before disconnecting a negative wire from the battery make sure that you have that for system input in action after completion of works.

  1. Give four fixing nuts and disconnect the safety cushion module from a steering column. Disunite the electric socket of the module. At work with the module always hold it the open party from own body. Always put the module on a workbench or other surface the open party up (at all down!).
  1. For removal of the module of a safety cushion give the top nuts (right top nuts occupies the same situation from the opposite side of a steering wheel).

… and the bottom nuts (the right is located similarly from the opposite side from a steering wheel).

  1. Release lock uvulas and disunite the electric socket of the module of a safety cushion.
  1. Give a nut of fastening of a steering wheel, then mark the provision of a steering shaft on the relation to a nave (if such labels are not put not so or if they are not combined) for the purpose of simplification of the subsequent assembly.

Do not allow a provorachivaniye of a steering shaft after removal of a steering wheel.


  1. Before removal of a steering wheel make sure of combination of adjusting labels on its nave and a pin of a shaft of a column (if those are available); if labels are absent, put them independently by means of a chertilka or white paint.
  1. By means of a stripper remove a steering wheel from a shaft. At all it is not necessary to force down a wheel from a shaft a hammer.
  1. Remove a steering wheel from a shaft only by means of a stripper AT ALL SBIVYTE IT the HAMMER!
  1. If the provision of operated wheels during performance of procedure did not change (they remained are directed rectilinearly), now it is possible to establish a steering wheel into place. If wheels turned, it is necessary to make centering of a spiral spring of a safety cushion. For this purpose establish forward wheels strictly rectilinearly and rotate a rotor of an hour spring clockwise against the stop (it is not necessary to make too big efforts). Now turn a rotor on two and a half turns counter-clockwise. In this provision of a wire of a horn there should be above, and wires of the module of a pillow - below.

Details of an hour spring of a safety cushion.

  1. For installation of a steering wheel achieve combination of adjusting labels on its nave and a shaft pin. Establish a nut and tighten it with demanded effort.
  2. Establish into place the safety cushion module. Screw four fixing nuts and tighten them with demanded effort.
  3. Connect a wire to the negative plug of the battery