Jeep Grand Cherokee

1993-1999 of release

Repair and car operation



Jeep Grandee Cheroki
+ Jeep Grand Cherokee brand Cars
+ Settings and routine maintenance
- Ryadny six-cylinder engine
   General information
   The repair procedures, which performance it is possible without engine extraction from the car
   Reduction in the provision VMT of a step of compression of the piston of the first cylinder
   Removal and installation of a cover of a head of cylinders
   Removal, check of a condition and installation of yokes and bars of pushers
   Replacement of klapanny springs, their plates and maslootrazhatelny caps
   Removal and installation of the inlet pipeline / final collector
   Removal and installation of a head of cylinders
   Replacement of a forward epiploon of a cranked shaft
   Condition check, removal and installation of a cover of a distributive chain, chain and its asterisks
   Removal, check of a condition and installation of a camshaft, bearings and hydraulic pushers
   Removal and installation of the pallet of a case
   Removal, check of a condition and installation of the oil pump
   Removal and flywheel installation / driving disk
   Replacement of a back epiploon of the crankshaft
   Check of a condition and replacement of rubber pillows of support of the engine
+ V8 Engine
+ Procedures of the general and major maintenance of the engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of onboard electric equipment
+ Governing bodies and operation receptions



Removal and flywheel installation / driving disk

Removal

 PERFORMANCE ORDER

  1. To Poddomkratta the car also establish it on props, then remove transmission (Head the Manual box of gear shifting). In case of existence of signs of leaks now it will be a high time to replace a forward epiploon / a sealing ring of the oil pump (AT only).
  2. Remove a basket and a conducted disk of coupling (Head Coupling and the transmission line) (RT). Now it is a high time to check a condition / to replace components of coupling and directing bearing.
  3. Paint or center punch mark the provision of a flywheel / a driving disk in relation to a cranked shaft for a guarantee of its correct installation at assembly.
  1. Before flywheel removal / a driving disk mark its situation in relation to a cranked shaft.
  1. Give bolts of fastening of a flywheel / a driving disk to a cranked shaft. If the cranked shaft thus starts to be turned, immobilize it, having jammed between a teeth of a wreath of a flywheel a screw-driver or having used as the lever mount.
  1. At an otdavaniye of fixing bolts hold a flywheel from a provorachivaniye by means of the lever.
  1. Remove a flywheel / a driving disk from a cranked shaft. As the weight of a flywheel is rather great, take care of its adequate support in process of an otdavaniye of the last bolt.

Edges of a gear wreath can appear very sharp - put on gloves.

Installation

 PERFORMANCE ORDER

  1. Wipe a flywheel, having removed from it oil and greasing traces. Check a flywheel surface on existence of the cracks left heads of rivets of furrows, spots of an overheat and задиров. Superficial scratches can be removed by means of a thin emery paper. Lay a flywheel on a flat surface and by means of a measuring instrument of planeness check it on existence of signs of a bend and deformations. In case of detection of serious defects it is necessary to give a flywheel to a pro-point in a car-care center workshop.
  2. Smooth out and interfaced surfaces of a flywheel / a driving disk and a cranked shaft, check their condition. If the back epiploon of a cranked shaft allows leaks, replace it before will start to establish a flywheel / a driving disk on a place (The section Replacement of a back epiploon of the crankshaft).
  3. Put a flywheel / driving a disk to a cranked shaft. Track combination of the landing labels put during dismantle. Pay attention that some engines are equipped with directing pins or non-uniformly located boltovy openings that does flywheel landing / a driving disk on a shaft quite unequivocal. Before installation of bolts grease their carvings with fixing hermetic.
  4. Jam a screw-driver in a wreath teeth for flywheel keeping / a driving disk from a provorachivaniye and tighten fixing bolts with demanded effort, operating in slightly (three) stages and passing from a bolt to a bolt in a diagonal order.

It is useful to note a head of each tightened bolt chalk is will allow to observe a due order of a tightening and to avoid the admission of bolts.

  1. Further assembly make as it should be, the return to a dismantle order.