http://www.norma-stab.ru/stabilizire_vibor.html .

Jeep Grand Cherokee

1993-1999 of release

Repair and car operation



Jeep Grandee Cheroki
+ Jeep Grand Cherokee brand Cars
+ Settings and routine maintenance
+ Ryadny six-cylinder engine
+ V8 Engine
+ Procedures of the general and major maintenance of the engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
- System of electric equipment of the engine
   General information
   Engine start from an auxiliary source
   Check of a condition and replacement of wires of the battery
   Removal and battery installation
   Ignition system - the general information
   Check of serviceability of functioning of system of ignition
   Check of serviceability and replacement of the coil of ignition
   Check of serviceability and replacement of the sensor of provision of a camshaft
   Removal and distributor installation
   Charge system - the general information and precautionary measures
   Check of serviceability of functioning of system of a charge
   Removal and generator installation
   Start system
   Diagnostics of malfunctions of a starter without its removal from the car
   Removal and starter installation
   Removal and installation of the traction relay (engines in volume of 4.0 l)
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of onboard electric equipment
+ Governing bodies and operation receptions



Ignition system - the general information

Applied on these cars of transistor type the electronic system is capable to develop much stronger currents, than ignitions of usual type made by systems. At service of system observe special precautionary measures.

All models are equipped with the computerized system of ignition into which structure enter the ignition coil, sensors of provision of distributive and cranked shaft and the Module of management (RSM). RSM carries out control of moment installation (an advancing corner) ignitions, spark and advancing characteristics. Installation of a corner of an advancing of ignition is not subject to adjustment and change of position of the distributor to its change does not conduct.

On engines in volume of 4.0 l position of the distributor is fixed unequivocally at the expense of a directing groove on its case. Clamping the bolt of fastening of the distributor at the correct installation passes through this groove. On models in volume of 5.2 l the fixing collar clamped by a bolt allows to rotate freely the distributor, however it does not conduct to change of installation of a corner of an advancing of ignition. Do not try to modify a corner of an advancing of ignition, rotating the distributor.

The distributor drive (its conducted gear wheel), including a begunok, is carried out from a camshaft. The sensor of provision of a camshaft is located in the distributor and carries out transfer on the processor of the signals which are responsible for synchronization of supply of fuel in cylinders.

Earlier the sensor of provision of a camshaft was mentioned in lists of spare parts of dealer offices of Chrysler firm as plate assembly. Some models are equipped with the independent sensor of a camshaft which easily acts in film from the distributor without extraction of last of the car. On other models sensors of a camshaft of the dependent type, demanding removals of the distributor are established.

The computerized system of ignition provides complete control of installation of a corner of an advancing of ignition by determination of optimum current value on the basis of the analysis of information received by the microprocessor from sensors of speed of movement of the car (VSS), temperature of a cooler, the provision of a butterfly valve (TPS) and absolute pressure in the pipeline (MAR). The corner of an advancing of ignition changes during an engine warming up, at its work on single turns and normal functioning of the warmed-up engine. Management of installation of a corner of an advancing of ignition carries out the module of management (RSM). The structure of such electronic system of ignition includes also the ignition lock, the battery, the coil, the distributor, spark plugs and candle wires.

Of acquisition of replaceable components and assemblies of the distributor address in dealer offices of firm. Check of serviceability of the sensor of provision of a cranked shaft is described in the Head of System of decrease in toxicity of the fulfilled gases and engine management.