Jeep Grand Cherokee

1993-1999 of release

Repair and car operation

Jeep Grandee Cheroki
- Jeep Grand Cherokee brand cars
   + Identification numbers of the car
   Acquisition of spare parts
   - Equipment of service, tool and workplace equipment
      Equipment of service
      Sizes of fixture
      Procedure and order of a tightening of carving connections
      Dismantling of components
      Prokladochnye of a surface
      Councils on removal of hoses
      Workplace equipment
   + Poddomkrachivaniye and towage
   Engine start from the auxiliary power supply
   + Automobile himikaliya, oils and greasings
   + Diagnostics of malfunctions
+ Settings and routine maintenance
+ Ryadny six-cylinder engine
+ V8 Engine
+ Procedures of the general and major maintenance of the engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of onboard electric equipment
+ Governing bodies and operation receptions


The choice of the good tool is one of the main requirements for everyone who plans independent performance of procedures of maintenance or car repairs. At first sight the expenses connected with acquisition of the demanded set of tools, can seem too big, however at their sravnivaniye with the expenses interfaced to performance of procedures of routine maintenance and the elementary car repairs at car repair shop, will appear quite reasonable.

To help the average motorist with a choice of the tool necessary at carrying out various procedures on the care of the car, described in this Management, the lists of three tool kits which have been conditionally entitled as below are provided: a tool kit for routine maintenance and the minimum repair; a tool kit for the general and major maintenance and the special tool. The owners of cars who do not have practical experience of carrying out mechanical works, should begin with performance of the procedures limited to use of tools from the first list, increasing thus the qualification and gradually expanding a range of the applied tool. In process of acquisition of experience it is possible to pass to performance of more complex challenges, supplementing a tool kit available on hands. After a while the received skills will allow to start performance of more difficult works demanding use of the tool from the second list (for the general and major maintenance of the car). When your qualification will start to allow to save considerable means on independent performance of difficult repair procedures, it is possible to think of acquisition of the special tool from a special set.

Micrometer set
Set of a tsiferblatny measuring instrument
Tsiferblatny calliper
The vacuum pump with a manual drive
Compression measuring instrument with a nozzle for installation in a candle opening
Stripper for damper removal / a steering wheel
Stripper of general purpose
The tool for removal of hydraulic pushers
The tool for compression of klapanny springs
The tool for compression of klapanny springs
Vertical drill for removal of step wear in the cylinder
The adaptation for pro-cleaning of flutes of piston rings
The tool for removal/installation of piston rings
The tool for a staving of piston rings
Hon for processing of a mirror of cylinders
The tool for removal of hats of springs of brake boots
Hon for processing of brake cylinders
The tool for centering of disks of coupling
Set of taps and lerok

Tool kit on routine maintenance and the minimum car repairs

The list provided below includes a minimum of procedures of routine maintenance necessary for performance and insignificant car repairs of tools. Acquisition of a set of the combined wrenches (with a usual rozhkovy head on one end is recommended and with cap on other), despite big cost of such set in comparison with cost of a set of usual rozhkovy keys, expenses will be justified, since these keys possess advantages of both types.

  • Set of the combined keys (1/4-1 inch; 6-19 mm)
  • Adjustable spanner
  • Candle key (with a rubber insert)
  • The tool for adjustment of a candle gap
  • Set measuring щупов
  • Nippelny key for pumping of brakes
  • Screw-drivers:
    • With a flat sting (150 mm in length and 8 mm in diameter)
    • With a krestovy sting (No. 2 x 6 of inches (150 mm in length)
  • The combined flat-nose pliers
  • Hacksaw on metal with a set of cloths
  • Manometer for pressure measurement in tires
  • Lubricant gun (syringe)
  • The canister under oil
  • Thin emery paper
  • Wire brush
  • The tool for cleaning of plugs and contacts of wires of the battery
  • Key for removal of the oil filter
  • Funnel (the average size)
  • Props for car fixing in the lifted condition (2)
  • Drain capacity

If procedures of routine maintenance include carrying out base adjustments, acquisition of high quality of a stroboscope and the combined tachometer/tool for measurement of duration of the closed condition of contacts of the breaker is required also. In spite of the fact that these tools are a part of the list of special tools, the mention of them here is given in a type of an absolute necessity of their application for carrying out high-quality control of ignition of the engine, being part of procedures of routine maintenance of the car.

Tool kit for the general and major maintenance of the car

This tool is necessary at carrying out any operations on repair of the engine of the car and it is offered in addition to the first list. This list includes a complete set of replaceable face heads. At considerable cost, the set of replaceable heads brings invaluable advantage, thanks to the universality and convenience in the address, - in particular in a combination with entering into a set of various type drives. Of 1/2 inches are recommended to use preferably drives section (instead of 3/8 inches) since they, though are more expensive, can be used practically with any type of dinamometrichesky keys (in an ideal, the good mechanic should have at the order both such as drives). Cheaper alternative to a set of replaceable face heads is the set of tubular keys.

  • Set of replaceable face heads (including Torх type heads) (or tubular keys), the sizes corresponding to the sizes of wrenches from the previous list
  • Ratchet reversive drive (for use with replaceable face heads)
  • Collar in length of 250 mm
  • Universal (kardanny type) the hinge (for use with face heads)
  • Dinamometrichesky key (with a drive of the same size, as for replaceable face heads)
  • Hammer with round the brisk - 8 ounces (about 230 g)
  • Hammer with soft brisk (plastic or rubber) (kiyanka)
  • Screw-drivers:
    • With a flat sting (length of 150 mm and about 6.5 mm in diameter)
    • With a flat sting (strong mm No. 2, 8)
    • With a krestovy sting (No. 3 x 8 of inches of 203 mm)
    • With a krestovy sting (strong No. 2)
  • Clamping pincers
  • Flat-nose pliers:
    • For electricians (with the isolated handles)
    • Uzkonosye (nippers)
    • For lock rings (internal and external)
  • Chisel - 1/2 inches (13 mm)
  • Scraper (made of the copper tube flattened out and pointed from one end)
  • Skrayber (chertilka)
  • Center punch
  • Small beards with a thin sting (1.6, 3.2, 4.8 mm)
  • Steel line/measuring instrument of planeness
  • Set of keys-shestigrannikov (Allen) (for heads with an internal shestigrannik)
  • Set of files
  • Wire brush (big)
  • Second set of props
  • Jack (hydraulic or nozhnichny type)

One more constantly required tool is the electrodrill with the boss on 3/8 inches (to 9.5 mm) with a set of high quality of drills.

Special tool

The tools being adequately expensive, not required regularly, or demanding at using of implementation of instructions of manufacturers get to this list. If the sphere of your activity does not include frequent performance of difficult mechanical operations, acquisition of such tool will be a bad investment of means. It is reasonable to get it by sharing the cost with friends or to hire in car-care center workshops.

Only those tools which can be found in retail trade or which are issued for distribution on representation offices of firms are brought in the list. Sometimes in the Management text you will find references to such special tools. Usually authors try to offer in parallel the alternative method, allowing to avoid obligatory use of the remote tool. In case to avoid use of the special tool it is impossible, and its acquisition in using is problematic, performance of the corresponding works is better for entrusting specialists of car-care center.

  • The tool for compression of klapanny springs
  • The adaptation for pro-cleaning of flutes of piston rings
  • The tool for a staving of piston rings
  • The tool for installation of piston rings
  • Measuring instrument of extent of compression of gases in cylinders (компрессометр)
  • Vertical drill for processing of edges of cylinders
  • Hon for processing of mirrors of cylinders
  • Measuring instrument of diameter of cylinders
  • Micrometer (micrometers) and/or tsiferblatny calliper
  • The tool for removal of hydraulic pushers
  • Separator of spherical hinges
  • Stripper of universal type
  • Shock screw-driver
  • Set of a tsiferblatny measuring instrument
  • Stroboscope (with the inductive sensor)
  • The manual combined pump (vacuum/delivery)
  • The tachometer/tool for measurement of duration of the closed condition of contacts of the breaker
  • Universal tester for electric measurements
  • Elevating rigging
  • The tool for removal/installation of brake springs
  • Floor jack

Tool acquisition

To the beginner mechanic in respect of acquisition of the necessary tool for performance of procedures of routine maintenance and car repairs can be offered some practical advice. By preparation for carrying out procedures of routine maintenance or the minimum car repairs it is reasonable to get the tool separately. On the other hand, in case of planning of wide works, it is simpler and more reliable to buy a set of the modern tool in shop of retail network. Set acquisition usually manages slightly cheaper than individual purchases and is often supplemented with the enclosed tool box. Further, for choice expansion, separate tools, additional sets and a tool box of the bigger size can be bought in addition. Gradual expansion of a set of tools will allow to stretch expenses and to be defined in a choice of really necessary tools.

Specialized tool shops are the unique source of acquisition of some special tools, but, irrespective of a source, avoid cheap purchases, in particular at a choice of screw-drivers and replaceable face heads as term of their service for certain will appear short. Expenses connected with replacement and restoration of the cheap tool as a result will appear incomparably more considerable, than costs of single acquisition of the qualitative goods.

Care of the tool and its storage

The good tool is a valuable investment of means, therefore it is reasonable to take care of keeping it clean and constant availability for service. After using the tool before combining it in a storage place, always carefully wipe its surface pure dry rags, deleting from it traces of dirt, greasing and the remains of metal particles. Never leave the tool scattered on a workplace. After completion of works attentively check space under a cowl and under the car on existence of the forgotten tool.

For storage of such tool as screw-drivers, flat-nose pliers, hammers the tool comb fixed in a convenient place on a wall of garage, etc. is ideally suited. Sets of wrenches and replaceable face heads should be stored in metal boxes. The measuring tool should be stored in inaccessible to impact of corrosion, dry and pure places.

Always it is necessary to pay attention to a condition of working surfaces of the tool. The shock part quickly a hammer in the course of work is subject to a rasklepyvaniye, screw-drivers lose over time sharpening of the stings. Do not stint to give a little time and attention to that by means of an emery paper or a file to remove расклепы and to put in order cutting edges. It is irreversible the worn-out or damaged tool replace.

At careful leaving the tool will serve to you belief and the truth during very long term.