Jeep Grand Cherokee

1993-1999 of release

Repair and car operation


Jeep Grandee Cheroki
+ Jeep Grand Cherokee brand Cars
+ Settings and routine maintenance
+ Ryadny six-cylinder engine
+ V8 Engine
+ Procedures of the general and major maintenance of the engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
- Brake system
   General information
   System of anti-blocking of brakes (ABS) - the general information
   Replacement of blocks of disk brake mechanisms
   Removal, major maintenance and installation of a support of the disk brake mechanism
   Condition check, removal and installation of a brake disk
   Replacement of boots of drum-type brake mechanisms
   Removal, major maintenance and installation of wheel cylinders
   Removal and installation of the combined valve (regulator)
   Removal and installation of the main brake cylinder
   Check of a condition and replacement of brake hoses and lines
   Pumping of brake system
   Functioning check, removal and installation of the vacuum amplifier of brakes
   Functioning check, removal, installation and adjustment of the sensor switch of stoplights
   Adjustment of the parking brake
   Replacement of cables of a drive of the parking brake
   Replacement of boots of the parking brake (disk brake mechanisms of back wheels)
+ Suspension bracket and steering
+ Body
+ System of onboard electric equipment
+ Governing bodies and operation receptions

Replacement of boots of drum-type brake mechanisms

Replacement of boots of drum-type brake mechanisms should be made at the same time on both wheels - at all on one! Besides, it is necessary to pay attention that the dust developed by brake mechanisms in the course of their work can contain unhealthy asbestos. At all do not blow off a dust from surfaces of components of brake mechanisms the compressed air and do not inhale it. Works are best of all for making in a protective respiratory mask. At all do not use for cleaning of components of brake mechanisms solvents on an oil basis or gasolines - use only patent means for cleaning of brakes!


At the same time with boots surely it is necessary to change also clamping and returnable springs. Owing to cyclic thermal loadings to which springs continuously are exposed, later certain time they start to lose developed efforts that leads to a privolakivaniye of boots on drums and faster wear of working surfaces. At replacement of boots of brake mechanisms of back wheels use only the components patent and noted by a trademark approved to sale by local authorities.


 PERFORMANCE ORDER

  1. Weaken nuts of fastening of back wheels, поддомкратьте a back of the car and establish it on props. Block forward wheels wedges in order to avoid a car otkatyvaniye.
  2. Release the parking brake.
  3. Remove a wheel and a brake drum (Head of Control and routine maintenance).

All four boots of both back brake mechanisms should change at the same time, however, in order to avoid a casual pereputyvaniye of details work with each of mechanisms serially. Besides, the second thus can serve as a model of the correct assembly in case of any doubts.

  1. For performance of procedures of check of a condition and replacement of brake boots follow the scheme presented on illustrations below. Try not to break an operations procedure and attentively get acquainted with explanations to pictures.

If the drum does not give in to removal from a pin of a semi-axis and bashmachny assembly (Head of Control and routine maintenance), make sure that the parking brake is completely released, then moisten a joint between a nave and a drum getting oil. Let's to oil time be absorbed, then repeat attempt of removal of a drum. If attempt appears again unsuccessful, it is necessary to compress brake boots. For this purpose at first it is necessary to take a stopper from a board of the brake mechanism. After removal of a stopper take away the lever from an adjusting gear castor by means of a narrow screw-driver, and the second narrow screw-driver turn a castor so that boots departed from walls of a brake drum (see an illustration). Now the drum should act in film freely.


Components of assembly of a drum of the back brake mechanism - the left mechanism is shown.

  1. Before removal of any of components of the brake mechanism clean assembly by means of patent means and dry it - establish drain capacity under the brake mechanism for collecting washed-away dirt - AT ALL DO NOT BLOW OFF the BRAKE DUST the COMPRESSED AIR!
  1. Delay the lever of a regulator and turn an adjusting gear castor for branch of boots from drum walls.
  1. Delay back a cable of the device of self-regulation and push the regulator lever back, having unhooked it from a back boot of the brake mechanism.
  1. Remove from a basic finger returnable springs both (forward and back) boots - in a picture the tool for removal of springs (ask in shops of automobile accessories) which application allows to facilitate procedure performance essentially is shown.
  1. Remove from a basic finger a cable of a self-regulator and a finger plate.
  1. Disconnect from a back boot a returnable spring and directing a cable.
  1. Disconnect holding spring and a finger of a forward boot.

… then separate a forward boot and the adjusting screw from a brake board.

  1. Remove a strut of the parking brake.
  1. Remove holding and a finger of a back boot, then separate a boot from a board of the brake mechanism - having hooked the lever, remove a clip of the executive lever of the parking brake from an axial finger.

… then disconnect the lever from a back boot - try not to lose a spring washer.

  1. Grease contact surfaces of brake boots (arrow) with high-temperature greasing.
  1. Connect a new boot to the executive lever of the parking brake, establish a spring washer and a lock clip, having reduced its sponges by means of flat-nose pliers.
  1. Establish a back boot with a holding spring on a brake board, then place the end of a strut of the parking brake in reciprocal deepening (shooter).
  1. Grease the adjusting screw with high-temperature greasing.
  1. Press a forward boot to a brake board, then establish holding spring - track, that the rack of the parking brake and pushers of the wheel cylinder entered into gearing with cuts of boots.
  1. Establish a plate of a basic finger …

… and self-regulator cable.

  1. Pass the end of a returnable spring of a back boot through directing a cable, having hooked on it for an opening in a boot, then pull a spring, having fixed it on a basic finger.