Jeep Grandee Cheroki
+ Jeep Grand Cherokee brand Cars
+ Settings and routine maintenance
+ Ryadny six-cylinder engine
+ V8 Engine
+ Procedures of the general and major maintenance of the engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
- Body
General information
Care of a body
Care of the panels of furnish made of vinyl
Care of an upholstery and salon rugs
Repair of insignificant damages of body panels
Repair of considerable damages of a body
Service of loops and locks
Replacement wind and motionless glasses
Removal, installation and adjustment of provision of a cowl
Removal and installation of the lock of a cowl and cable of its drive
Removal and installation to the place of the panel of a decorative front grille
Removal and installation of a forward wing
Removal and installation of bumpers
Removal and installation of the panel of an internal upholstery of a door
Removal, installation and adjustment of provision of a door
Removal and installation of handles, cylinder and clamp (latch) of the lock of a door
Removal and installation of a windowpane of a door
Removal and installation of a regulator of a window of a door
Removal and installation of the central console
Removal and installation of the panel of an upholstery of a door of a back
Removal, installation and adjustment of provision of a door of a back
Replacement of an emphasis of a door of a back
Removal and installation of facing of a combination of devices
Removal and installation of facings of a control panel
Removal and installation of a control panel
Removal and installation of covers of a casing of a steering column
Removal and installation of rear-view mirrors
Remove also installation of a lattice of a fairing
Removal and installation of seats
Control body sizes
+ System of onboard electric equipment
+ Governing bodies and operation receptions
|
Removal and installation of handles, cylinder and clamp (latch) of the lock of a door
Door latch
|
|
- Completely lift glass of a window and remove the panel of an internal upholstery of a door and the water filter (The section Removal and installation of the panel of an internal upholstery of a door).
- Disconnect rods of drafts from a latch.
|
|
- Turn a plastic clamp up and disconnect rods of drafts of a latch.
|
- Give three fixing screws with TORX type heads. Probably, the stragivaniye of screws will need a shock screw-driver.
|
|
- Give a bolt of fastening of a latch.
|
- Remove a latch from a door.
- Put a latch on an adjusting place and screw fixing bolts. Strongly tighten bolts.
- Connect to a latch rods of drafts.
- Make sure of adequacy of locking of a door. In case of need make adjustment of provision of a latch (having weakened for this purpose bolts), achieving ease of a zashchelkivaniye of a door (the door handle thus should appear aflush with a door surface). After completion of installation weaken the adjusting screw of draft, having passed a key-shestigrannik of 5/32 inches (4,0 mm) in an access opening in a door end face. Weaken the adjusting screw and push it up on a cut for a choice of a weak point of draft, then tighten the screw.
|
|
- Pass a key-shestigrannik a head in an adjusting opening, weaken the screw and advance it up on a cut for sample of a weak point of draft.
|
|
|
Lock cylinder
|
|
- Remove the external handle of a door. Disconnect draft, having used a screw-driver for pushing out of the holder and extraction of the cylinder of the lock from a door.
- Installation make upside-down.
|
|
External handle
|
|
- Disconnect draft of the external handle (a remote drive) doors from a lock latch, give fixing nuts and remove the handle from a door.
|
|
- Details of installation of the external handle and cylinder of the lock of a door.
|
- Establish the handle into place, connect draft and screw nuts. Strongly tighten nuts.
|
|
Internal handle
|
|
- Give a fixing bolt, turn the handle forward and disconnect drafts, then remove the handle from a door.
|
|
- Give a bolt (shooter), turn the internal handle forward and disconnect rods of drafts.
|
|
|
|
|
