Jeep Grand Cherokee

1993-1999 of release

Repair and car operation



Jeep Grandee Cheroki
+ Jeep Grand Cherokee brand Cars
+ Settings and routine maintenance
+ Ryadny six-cylinder engine
- V8 engine
   General information
   The repair procedures, which performance does not demand engine extraction from the car
   Reduction in position VMT of the piston of the first cylinder
   Removal and installation of covers of heads of cylinders
   Removal, check of a condition and installation of yokes and bars of pushers
   Replacement of klapanny springs, their plates and maslootrazhatelny caps
   Removal and installation of the inlet pipeline
   Removal and installation of final collectors
   Removal and installation of heads of cylinders
   Replacement of a forward epiploon of a cranked shaft
   Removal, check of a condition and installation of a cover of the distributive chain, chain and its asterisks
   Removal, check of a condition and installation of a camshaft and hydraulic pushers
   Removal and installation of the pallet of a case
   Removal, check of a condition and installation of the oil pump
   Removal and flywheel installation / driving disk
   Replacement of a back radical epiploon
   Check of a condition and replacement of rubber pillows of support of the engine
+ Procedures of the general and major maintenance of the engine
+ Systems of cooling, heating and air conditioning
+ the Power supply system and production of the fulfilled gases
+ System of electric equipment of the engine
+ Systems of decrease in toxicity of the fulfilled gases and engine management
+ Manual box of gear shifting
+ Automatic transmission
+ Transfer case
+ Coupling and transmission line
+ Brake system
+ Suspension bracket and steering
+ Body
+ System of onboard electric equipment
+ Governing bodies and operation receptions


Replacement of a forward epiploon of a cranked shaft

Removal

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.
  2. To Otboltita a fan casing also shift it back, having transferred via the fan.
  3. By means of the lever turn a natyazhitel of a driving belt of hinged units it clockwise so that possibility to remove a tape belt from a tension roller was formed.
  4. Give bolts and separate a pulley of a cranked shaft from a damper of krutilny fluctuations.
  1. Give bolts of a pulley of a cranked shaft (arrow) and a big central bolt of a damper of krutilny fluctuations.
  1. Give a big bolt of a damper of krutilny fluctuations. For keeping of a cranked shaft from a provorachivaniye in the course of an otdavaniye of a bolt remove a starter (Head System of electric equipment of the engine) and ask the assistant to jam a big screw-driver in a gear wreath of a flywheel / a driving disk.
  2. By means of a special stripper (see an illustration in Head Ryadny the six-cylinder engine) (ask in shops of automobile accessories) remove a damper of krutilny fluctuations.

It is not necessary to use a stripper grasping edges of a damper. The stripper should fasten on bolts of a pulley and put effort only to a damper nave. Track also that the forward nozzle of a stripper was on diameter more than diameter of an opening in a forward end face of a cranked shaft.

  1. By means of the special tool or a big screw-driver take an epiploon from a cover of a distributive chain.

In order to avoid development of leaks try not to scratch and not to deform an epiploon nest.


  1. Extraction of a forward epiploon of a cranked shaft by means of a special stripper - try not to damage a surface of a pin of a shaft.

Installation

 PERFORMANCE ORDER

  1. Smooth out an epiploon nest, having removed from its surfaces all traces of a material of old laying and corrosion. Establish a new epiploon in a nest sponges (usually from sponges the broad spring) inside (to the engine is established). A small amount of oil put on external edges of an epiploon will facilitate installation - however be not overzealous in greasing.
  2. Begin to knock an epiploon in a nest before its complete landing in it by means of a big replaceable head and a hammer (see an illustration in Head Ryadny the six-cylinder engine). A head pick up so that its external diameter equaled to external diameter of an epiploon. Track, that the new epiploon "sat down" in a nest against the stop in a cover flange.
  3. Check a condition of a surface of a damper of krutilny fluctuations contacting to an epiploon. If the epiploon developed a flute in a surface, the damper can be restored by a press fitting in it the special loose leaf - address in a car-care center workshop.
  1. If the epiploon developed a flute in a sealing surface of a damper, the damper can be restored by a way of installation to it special loose leaf (ask in shops of automobile accessories).
  1. Grease epiploon sponges with pure impellent oil and establish into place a damper.